Stm32f407vg stm32f4discovery

From Miosix Wiki
Revision as of 22:07, 17 June 2015 by Fede.tft (talk | contribs)
Jump to navigation Jump to search
STM32F4DISCOVERY

Configuring the kernel

Unlike the stm32vldiscovery, this board has the STLink/V2 firmware which is much more Linux friendly. All you need is a recent version of OpenOCD and the QStlink2 tool to support ths board.

First, make sure the correct board is selected in the miosix/config/Makefile.inc file. The line defining the OPT_BOARD variable should be set to OPT_BOARD := stm32f407vg_stm32f4discovery, that is, that line should be uncommented, and the other commented out, like this: 

##
## Target board, choose one. This also implicitly select the target
## architecture
##
#OPT_BOARD := lpc2138_miosix_board
#OPT_BOARD := stm32f103ze_stm3210e-eval
#OPT_BOARD := stm32f103ve_mp3v2
#OPT_BOARD := stm32f100rb_stm32vldiscovery
#OPT_BOARD := stm32f103ve_strive_mini
#OPT_BOARD := stm32f103ze_redbull_v2
OPT_BOARD := stm32f407vg_stm32f4discovery
#OPT_BOARD := stm32f207ig_stm3220g-eval
#OPT_BOARD := stm32f207zg_ethboard_v2

In addition, this board has a couple of board-specific options in the Makefile.inc file. For convenience, the relevant part of that configuration file is reported here so as to be easily located within the file 

##---------------------------------------------------------------------------
## stm32f407vg_stm32f4discovery
##
ifeq ($(OPT_BOARD),stm32f407vg_stm32f4discovery)

  ## Linker script type, there are two options
  ## 1) Code in FLASH, stack + heap in internal RAM (file *_rom.ld)
  ## 2) Code + stack + heap in internal RAM (file *_ram.ld)
  LINKER_SCRIPT_PATH := arch/cortexM4_stm32f4/stm32f407vg_stm32f4discovery/
  LINKER_SCRIPT := $(LINKER_SCRIPT_PATH)stm32_1m+192k_rom.ld
  #LINKER_SCRIPT := $(LINKER_SCRIPT_PATH)stm32_1m+192k_ram.ld

  ## This causes the interrupt vector table to be relocated in SRAM, must be
  ## uncommented when using the ram linker script
  #SRAM_BOOT := -DVECT_TAB_SRAM

endif

As can be seen, the file is made mostly of comments, and defines three options: LINKER_SCRIPT and SRAM_BOOT. The comments explain in detail the meaning of there options, so it isn't necessary to further explain them.

After modifying configuration files it is recomended to do a make clean; make (or in the Netbeans IDE, to click on the "Clean and build project" button) to be sure that changes are applied.

Loading code

As explained before, there are more than one linker script for this board, and the selected linker script affects the way code should be loaded on the board.

  • The stm32_1m+192k_rom.ld is the default linker script, and put the code in FLASH, so you need to program the microcontroller's FLASH every time you change your code, but code will run faster and won't be lost at each reboot.
    A simple way to load code in FLASH is to use the QStlink2 tool.
  • The stm32_1m+192k_ram.ld linker script is very useful for debugging code on this board, as it locates everything (code, stack, heap) in the microcontroller's RAM. It has the disadvantage that the loaded code is lost upon reboot (being in a volatile memory), but for debugging, it is not an issue.

Serial port

The board has no serial to USB adapter onboard, so you need to use an external one, connected to USART3, in detail PB10 (TXD) and PB11 (RXD). The choice of USART3 was done due to the fact that USART1 pins are not free on this board.

In Circuit Debugging

Before you begin you should note that the Miosix kernel will put the CPU to a low power state when no thread is running. This low power state will usually confuse debuggers and make them lose sync with the CPU. To avoid this you need to edit the miosix/config/miosix_settings.h file and uncomment 

#define JTAG_DISABLE_SLEEP

This will prevent the kernel from putting the CPU in its low power state making debugging possible. Also, to be able to precisely single-step your code you need to disable compiler optimizations as gdb is incapable of reliably debug an optimized code. The option is in the miosix/config/Makefile.inc file and is the OPT_OPTIMIZATION := -O0 that should be uncommented while the other lines related to the same option should be commented out.

After modifying configuration files it is recomended to do a make clean; make (or in the Netbeans IDE, to click on the "Clean and build project" button) to be sure that changes are applied.

Since the board has an on board SWD in circuit debugger, simply plugging the USB cable is all you need from an hardware point of view. On the software side, you need to open two shells. In one do a 

sudo openocd -f miosix/arch/cortexM4_stm32f4/stm32f407vg_stm32f4discovery/stm32f4discovery.cfg

This will start the OpenOCD program that will connect to the board and listen for GDB connections.

In the second shell type the following commands 

arm-miosix-eabi-gdb main.elf
target remote :3333
monitor soft_reset_halt
break main
continue

The first command will start the gdb debugger. The following commands are typed into the gdb console, and tell it to connect to OpenOCD, and reset the board and stop the program at the beginning of main() To load the program to be debugged, you can either do a make program before and then start debugging, or you can directly write the FLASH memory from within gdb with this command 

monitor flash write_image erase main.bin 0x08000000

From there on, consult a gdb reference on the Internet for information on how to single step code, set breakpoints and inspect variables.

(Optional) Configuring the Netbeans IDE

To have a fully working code completion that can also resolve the board-specific symbols, right click on the project, go to Set Configuration and select the right board. 

Netbeans-config.png

Miosix GPIO Mapping

SD Card

Connect VCC (3V) and GND using a 100nF capacitor between VCC and GND, this will be useful to overcome to current absorption peaks.

SD STM32 Optional
CLK PC12
CMD PD2
D0 PC8
D1 PC9 Y
D2 PD10 Y
D3 PC11 Y

Each connection needs a pullup resistor between ~47Kohm and 100Kohm.

Optional GPIOs are used in 4-bit mode.

Resource

stm32f4discovery Datasheet
Retrieved from "https://miosix.org/wiki/index.php?title=Stm32f407vg_stm32f4discovery&oldid=174"